You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.


  • Cart

  • Your shopping cart is empty!

Bluetooth ELM327 OBD2 Automotive diagnostic tester Car diagnostic tool Large spot

  • Product Code: Bluetooth ELM327 OBD2 Automotive diagnostic tester
  • Availability: 168

ELM-327 car diagnostic apparatus
Currently on the market points:
Plastic USB ELM327
Plastic Bluetooth ELM327
Aluminum Case USB ELM327
Mini Bluetooth
ELM327 is the latest PC-based OBD2 general-purpose vehicle diagnostic testing tool. It supports all OBD-II self-diagnostic systems and compatible communication protocol detection. ELM327 for the USB interface, through the RS232 conversion protocol to connect the laptop USB interface.
Support OBD-II vehicle diagnostic communication protocol:
..ISO15765-4 (CAN)
..ISO14230-4 (KWP2000)
Output protocol: RS232
Baud rate: 9600 or 38400
LED indicator: OBDTx / Rx, RS232Tx, power supply
Working voltage: 12v
Working current: 45mA
The ELM327 USBOBD-II self-diagnostic system uses software as a free program that allows you to use your PC and ELM327 to get all the information about your car engine computer. Software is easy to learn. The software supports DOS and Windows computer operating systems.
1. Read the generic and car manufacturer-specific diagnostic fault codes and display their definitions (the software contains more than 3000 fault codes)
2. Clear the fault code and turn off the engine (engine) fault alarm indicator
3. Read the engine real-time dynamic data stream
..Engine speed
Calculate the load value
Coolant temperature
Fuel system state
Short-term fuel correction
Long-term fuel correction
Intake manifold pressure
Timing ahead of time
Intake air temperature
..air flow
Throttle opening
Oxygen sensor voltage / short - term fuel fine - tuning
Fuel pressure. The The The
Supported models:
BMW West Jate Ford MINI Jaguar Mercedes-Benz Volkswagen
Chrysler Dodge Acura BYD F3 / F0 Chery 09 Alto
Suzuki Honda Toyota Mazda Mitsubishi Nisans Barro
Land Rover Chevrolet Kodak Infiniti Kia Modern
Odysa Bo Bo Po Citroen Peugeot Volvo Fiat and so on
Installation and use instructions
LM327 car diagnostic equipment installation and use instructions
Car fault code
Automotive Diagnostics
This product supports models using OBD-II protocol (including VPW, PWM, ISO, KWP 2000, CAN protocol) produced after 1996. You can connect the product to a laptop or desktop computer, used to read the fault code and know the meaning of the fault code, clear the car`s fault code, display the sensor data flow (such as speed, water temperature, etc.) ... ... very powerful!
This product supports all OBD-II protocol, USB interface output, more convenient to connect to the laptop.
Product Features:
OBD-II protocol: ISO15765-4 (CAN)
ISO14230-4 (KWP2000)
J1850 VPW
J1850 PWM
Output interface: USB
LED indicator: OBD transmit / receive, RS232 transmit / receive, power supply
Operating voltage: 12V, (with short circuit / overvoltage protection)
Product Features:
Read the fault code and know the meaning of the fault code, clear the car`s fault code, display sensor data (including: engine speed, coolant temperature, vehicle speed, intake manifold pressure, intake air temperature, air flow, throttle position , Oxygen sensor voltage, fuel pressure, etc.) There are other more advanced features ...
Graphics interface software commonly used are: Scantool, Scanmaster, Proscan, PcmSCAN, Digimoto, you can also use the super terminal with AT command to use.
Installation instructions: (Tips, if you can not read the software on the installation CD, please download the software from the following link :)
1, car information reading software ScanTool (dot) net:
2, USB driver:
installation steps:
1, install the CD or download the ScanTool (dot) net software.
2, the OBD-Ⅱ cable and automotive ODB-Ⅱ interface connection.
3. Connect the OBD-II cable to the ELM327. At this time, the power light (light) will light, ODB TX / RX light will flash, indicating that the connection is normal.
4, the USB cable to the ELM327 connected with the computer. At this point the computer will prompt to find the new hardware, according to the computer prompts to install the CD or the network to download the USB driver. Into the computer`s "Device Manager" click on the port, you will find the newly installed hardware "USB Serial Port", write down the COM number on the right. (The COM number will be used in the next step in the software settings)
5, start ScanTool (dot) net software. Open the ScanTool (dot) netv1.13 for windows program, select the options item, select the COM number you typed in the previous step, and then OK. So that the software installation is complete, you can diagnose your vehicle.

Overall Rating 5
Write a review
Note: HTML is not translated!
    Bad           Good